CoolMiniOrNot Forums -
  • Basic basing

    Basic Basing
    What is basing?
    Well, it's just a matter of applying some material to the base of the miniature,
    to make it look like it is standing on some type of surface. This is going
    to have to be up to you as to what you want it to look like. You might
    like to have them standing on grass, sand, rocks or even grid mesh. But
    what ever you choose, it is a good idea to continue the same base throughout
    you whole army. That way they will look more unified.
    As most
    gaming tables that I play on are 'grass' based, I prefer to use a grass
    look on my models also, as it helps to blend them in. Sometimes I think
    the model is just standing there on it's own two feet, without a base at
    all. But then again, that could be the coffee doing strange things to my
    eyesight.
    There is
    only one thing that you are definitely going to need and that is PVA (Poly
    Vinyl Acetate) Glue, in other words, wood glue. Other than that, the material
    that you decide to stick to the base is up to you. There are many different
    ways that you can go about it. Such materials as sand, painted over when
    it is dry, or even flock (finely mulched wood shavings that are dyed with
    a particular colour) are just a couple of them.
    Anyway,
    I prefer one particular method that is quick and simple and my preference
    of basing material is green flock. Firstly, I apply a coat of Goblin Green
    to the whole of the base, being very careful not to get any on the miniatures
    feet and that it is solid in colour. This way, when I have finished the
    base entirely, the black base will not show through the flock in any way
    at all, just to be safe. Even though the base does end up totally covered
    in flock, the green paint will eliminate any chance of this problem. Below
    is a picture of a base which has been painted.







    When painting
    the base make sure that the glue you used to fix the model to the base
    is completely dry, otherwise there is a chance that you will get glue on
    your brush and ruin it. The next step I use is to apply the PVA. I put
    a small amount of glue on my mixing palette, away from where I mix my paints,
    and use a very old brush to apply it to the base. The trick is not to get
    it on the feet of the miniature, otherwise when I go to put on the flock
    it will stick. To avoid this I make sure that when I put the brush to the
    base that it is flat against the surface. Sometimes the models feet don't
    actually come to rest on the base, for some type of moulding reason, but
    this helps me anyway. I can then slide the brush under the feet to apply
    the glue. I then wash out the brush very thoroughly, so that it wont go
    hard and I will be able to use it again next time. Just make sure that
    you use different water to that of your cleaning water. You don't want
    glue to end up on your paint brushes. Here is what my glue ends up looking
    like.







    As you can see,
    I don't use much glue. Just enough to cover the base in a thin layer. Then
    while the glue is wet I transfer it over to my flock pot. I like to keep
    my flock in a sealable container which makes it easy to get my miniatures
    in and out of quite easily. By immersing the base into the flock, I make
    sure that it is covered completely, then take it out and give the side
    of the base a tap with my finger to remove any excess. Voila. One based
    miniature. Here is what it looks like finished.







    So as you can
    see, it is quick and simple for me. Other people like to use sand as a
    basing material and then paint it with a basecoat, shade and highlight.
    Sometimes
    it can be good to add little bits of detail to the base to make it stand
    out that little bit more. Such things might include rocks, tall grasses,
    or even victim parts, like heads. But I only use these on character models
    as they deserve the attention to detail. I'll be covering this more intricate
    area at a later date.







  •  Articles order

    sort by Set Ascending

    Recent Articles

    gunrunr-143102

    How to make a cheap yet effective spray booth.

    Hello everyone. I'm here to show you how to make a nice spray booth for airbrushing. I took what I learned from watching different videos and came up with what worked best for me. After collecting all the items, the job of putting everything together actually only took me about 30 minutes. Below is the list of items you will need.

    1.) Plastic storage tub $6-$10 (Mine was free because I found it in the garage).
    2.) Ventilation fan $18
    3.) Air... read more
    gunrunr 04-07-2017, 07:00 PM

Privacy Policy  |   Terms and Conditions  |   Contact Us  |   The Legion


Copyright © 2001-2018 CMON Inc.

-->