• My Beastmen, and layering

    I'm certainly not the best painter, and this is not an article on how to paint golden demon

    quality mini's. However, this painting method will yield an excellent table top army. I

    also want to show some other people the technique of layering. It took me a while to

    actually try it, but it works very well. I got the technique from the book "How to Paint

    Citadel Miniatures."

    Layering is a technique for someone with more patience then skill. It's not very hard, it

    just takes a subtle touch with the brush, and some good brush control. Miniatures, altho

    they're 3 dimensional, appear flat, unless you enhance them with proper painting. So, we

    paint in where the shadows and highlights should go.



    In photoshop, we'd blur the final step, but we can't do that in real life When viewed

    up close, the hard edges do look fake, but most figures won't be viewed so closely. The

    next step up skill-wise is blending. Blending is mostly the same thing, but there are no

    hard edges. It's extremely hard and extremely time consuming.
    [pagebreak]

    First, I assembled the minis, glued sand to the base, and base coated them with Bleached

    Bone. I painted the base, drybrushing grey then white over the sand. I then washed the

    base in Flesh Wash, and painted the edges with Dark Angel Green.

    I then washed the figures in black, then a mix of black and Flesh Wash, and then just plain

    Flesh Wash.



    I then went over the flesh with Beastial Brown, and painted the eyes red. I used multiple

    thin coats, and left some of the innermost darkest spots showing thru.



    Over that, I painted "poison flesh" from Vallejo. Like in my above example, I made sure to

    leave a little bit of the bottom layer showing.



    and the back



    Next I made a custom mix of pale flesh and poison flesh, to get a pale skin tone.




    I think he's a bit too contrasty, so I gave another Flesh Wash. This tied the colors in

    better.



    Over that, I did an even paler mix of the skin color.




    At this point, the skin tones are pretty much done. The pictures on most monitors will be

    bigger then the actual figure is, so it looks like a sloppy paint job. When viewed on a

    table top, however, it's a very neat effect.
    [pagebreak]

    Next was the hair, weapons, and horns.




    I painted the weapons, armor, and fur chaos black. I used a light yellow color on the belt

    and hairbands.

    I drybrushed the hair in grey, to make it stand out a little more.



    I thought that looked a bit too grey, so I gave it a wash of thin black paint. I also put

    a wash in between the fingers, in the mouth, to make them stand out a little more.




    Black is hard to do without making it look grey. I didn't want an "old man" beastherd, so

    I left the highlighting very subtle. I also painted besital brown into the center of the

    belt and hairbands, leaving the yellow on the edges. I find it easier to do this, then the

    traditional method of painting the highlight color along the edges.


    [pagebreak]

    Next, I painted the weapons silver, along with the armor on his wrists and the tip of his

    horns. The rings on the swords were picked out in "beaten copper", along with the gen on

    his chest, and the edges of the wrist armor.



    On top of the silver, I painted flesh wash. This gives the metal a bronzy look. I don't

    think feral beastmen would keep their armor clean and shiny, so this dirties it up a bit.



    I saw an interesting technique in White Dwarf. To make his nurgle army look like they had

    diseased weapons, he sprinkled salt on them while the paint was drying. I wanted to try

    it, see if I could make the swords look corroded.



    That's with the salt, and afterwards


    Not quite the same result, but it's certainly not a clean, neat weapon. It looks more like

    the rusted chunk of iron a beastman would carry.
    [pagebreak]



    As a unit on the battlefield, their colors tie them in together, and they look coherent. I

    plan on adding some static grass, but otherwise, the color scheme I used on this page will

    be used on all of them.

    Layering is pretty simple, and gives dramatic results. It's much better then just painting

    flat colors and trying to use washes and drybrushing.


  •  Articles order

    sort by Set Ascending

    Recent Articles

    gunrunr-143102

    How to make a cheap yet effective spray booth.

    Hello everyone. I'm here to show you how to make a nice spray booth for airbrushing. I took what I learned from watching different videos and came up with what worked best for me. After collecting all the items, the job of putting everything together actually only took me about 30 minutes. Below is the list of items you will need.

    1.) Plastic storage tub $6-$10 (Mine was free because I found it in the garage).
    2.) Ventilation fan $18
    3.) Air... read more
    gunrunr 04-07-2017, 07:00 PM

Privacy Policy  |   Terms and Conditions  |   Contact Us  |   The Legion


Copyright © 2001-2016 CMON Inc.

-->