• First Article- Simple Basing

    So I was working on the base for my trollblood guy and I though I might as well take advantage of this opportunity to bring you guys our first article on basing. I was going for a pretty simple base with a bit of a marshy feel. So lets get to the fun stuff! Ok so to start off I made a mass of milliput in the rough shape of a rock. At this point you can't really make it look rigid and rock like but dont worry about it that will be taken care of in the next step. Once the putty has dried, take a hobby knife and cut away at any curved or rounded surface or edge on your rock until everything is sharp and rigid. Remember your are not cutting away big chunks, you should have already built the basic shape of the rock in the previous stage, you are just making small cuts on the surface. You may be thinking why not just use a real rock? Well that would be wonderful if you have the perfect one for the job but often times your model may not fit nicely on it and this is a way of making sure you have a perfect fit!


    For this base I wanted to add some small pools to create the marshy look so at this stage I layed down some putty where the ground would go and I left out the areas where the pools of water go. [The white looking putty is the groundwork]

    Once that putty has also dried, cover all of the ground area with glue and sprinkle some sand on the raised ground areas and overtop of that and in depressed areas where the pools go sprinkle some fine dirt. You could just use sand but it will give you a much more textured look which wasnt really appropriate for the wet muddy look of the marshes.
    TIP: Sandy dirt from outside is great for its variety of shape, its fine texture and its dirt cheap cost! (hah!)


    After doing all the texturing, I like to spray the base lightly with white primer to make it easier to paint. [Dont go too heavily just one or two spurts to make it easier for the paint to cling to the edges and raised areas]


    This is where the basing turns more specific, it gets more complex because the goal I am after is a marsh base so in order to make this standard base feel more marsh like I've done some more in depth colouring and applied some water and so on to make it fit with the theme of my Trollblood. The following parts are optional. You may take the above and paint it in desert colours, dark colours, or change it to another environment type!
    When painting the rock I used charadon granite and trollblood highlight (colors which I used in some of the finer details of my trollblod guy) and then I used some enchanted blue for the shadows (the color I used for the skin).


    Before I started painting the ground, I covered it all with some dry pigments. This stage wasnt really for coloring purposes, rather I've found that if you take a heavy layer of pigment and add water to it, it creates a nice muddy effect. though I have found that the downside to this technique is that if you uses heavy washes and press down on the pigmented areas too hard the color will get moist and mix in with your other colors.


    Next I began coloring the ground of the base with the same colors I used to shade the armor on the trollblood guy. The reason for choosing the same colors for the base as were used on the figure is to help the figure feel like he is within the environment rather than seperate from it (because light bounces off objects and is essentially what gives us color, the colors of the environment are likely to appear, even if only subtly on the figure and vice versa. This is quite an extensive topic which will be covered in greater detail in future articles!). I started first with a wash of snakebite leather, then dark flesh. After those two layers I went in with watered down brown ink. I applied the brown ink more heavily in the areas near where the water is going to go because wet earth is of course darker than dry earth. After all the washes of brown ink the earth was starting to look a little too dark s I re-added some brightnes to it by dabbing on a mix of trollblood highlight and snakebite leather. Finally for the areas where the water would go, I used a mix of enchanted blue and chaos black to create some depth of shadow with color because the depth was not physically there. I also did a light wash of blue over the entire base to give it the feel of a cool environment.



    For the next step I added some moss around the rock. For this I used GW flock and overtop I sprinkled some fine dirt to lessen the texture of the flock. After that I used the same pigment technique which I used to create the muddy look on the ground. This step was more experimental and it did not quite give me the effect I desired in the end. I decided to include this anyway as a reminder that while articles like this can be helpful, they are not a prescription and you should always experiment with new approaches to what you or others have done before! I also applied the static grass at this stage. Next I added some washes of darkened snot green to both the moss and the static grass. You can apply it over the whole surface of the moss but for the static grass you mainly want to apply the washes around the sides so that you don't crush all of the fibres down. And finally I added some specks of green in the area of the pools to resemble some plants in the water.




    Finally I cut the bristles off of a big old brush that I had and glued them to the base to resemble taller grasses or reeds, and I applied the water effects. In the final stages I reworked some washes of brown ink and blue to achieve the darkness of the earth that I wanted. I also worked the brown and blue into the rock in order to make it feel like it was more part of the ground than separated from it.


    Now all we do is wait for it to dry!

    Final Shot:

    http://legionofthecow.files.wordpres...hol1.jpg?w=388
    OR



    Hammer
    Legion of the Cow
    LegionoftheCow.wordpress.com
    This article was originally published in forum thread: First Article- Simple Basing started by LegionoftheCow View original post
    Comments 3 Comments
    1. shlaeNg's Avatar
      shlaeNg -
      Large pics are broken.
    1. Stilton's Avatar
      Stilton -
      Quote Originally Posted by shlaeNg View Post
      Large pics are broken.
      No pics at all for firefox.

      And what is a 'guide' article describing colours without pics, not much..
      Praps its just firefox.
    1. CyberPAddy66's Avatar
      CyberPAddy66 -
      Quote Originally Posted by Stilton View Post
      No pics at all for firefox.

      And what is a 'guide' article describing colours without pics, not much..
      Praps its just firefox.
      Doesn't work in Chrome either
  •  Articles order

    sort by Set Ascending

    Recent Articles

    gunrunr-143102

    How to make a cheap yet effective spray booth.

    Hello everyone. I'm here to show you how to make a nice spray booth for airbrushing. I took what I learned from watching different videos and came up with what worked best for me. After collecting all the items, the job of putting everything together actually only took me about 30 minutes. Below is the list of items you will need.

    1.) Plastic storage tub $6-$10 (Mine was free because I found it in the garage).
    2.) Ventilation fan $18
    3.) Air... read more
    gunrunr 04-07-2017, 08:00 PM

Privacy Policy  |   Terms and Conditions  |   Contact Us  |   The Legion


Copyright © 2001-2016 CMON Inc.

-->