Originally Appeared on The Fire of Nocturne.

http://www.thefireofnocturne.com

This is my first tutorial on sculpting (and a bit on painting) ever. Don't know if its good or not and I can only hope that it will turn out to be helpful for some people reading it. As it was also my first "serious" attempt with a digital camera some pictures are of a very poor quality. I'm sorry about that but as a photographing-rookie I made my best to make sure at least the majority of pictures were of enough quality that they would make this tutorial understandable.

If you have questions, critique or new ideas go ahead and post them. Maybe if there is a popular demand about sculpting and/or painting something in particular I might consider doing it and adding to the tutorial. That is if I am capable of doing just that.

These were the tools used. A pocket knife and a scalpel. The greenstuff itself can be made to have different properties. If you mix in more yellow you'll get a sticky, hard to work stuff that is perfect for really tiny detail. Another downside is that it will also take several days (not hours) to dry.

On the contrary, more blue will provide with an un-sticky and a bit harder stuff that is perfect for bigger areas and details.

To battle sticky greenstuff I use a piece of cloth with a drop of oil soaked in it. I simply put my fingertip or brush the blade of my knife along the oily cloth and that will then be perfectly free from sticky greenstuff without having to apply drops of water. Water is a bad idea since the amount often used will distort the visual of the greenstuff underneath it making it hard to actually sculpt details in it.

To ensure that no fingerprints are left use the finger nails to flatten out the greenstuff as a finish touch. Nails have much less tendency to stick to greenstuff.

Start with a simple shoulder pad (it doesn't have to be cleaned or free from "fat" at this stage) glued on a piece of plastic sprue to ease the holding and handling of it. Apply flattened out sphere of greenstuff to it in a way so that it will resemble a basic rough spiky shape with the edge of the flattened out stuff clearly brought out from the pad. This is quite easy accomplished by flattening the sphere of greenstuff with one finger while keeping another fingers nail underneath the edge.

---

---

---

--- ---
-----------------

When hardened use a knife (scalpel, pocket knife, whatever suites you) and cut a faint shape of the outer spikes like this. (you may want to use a micro pen to draw a shape before cutting) ---

--- -----------------

Now cut out the spikes and form them carefully (a sharp scalpel is better at this then a knife) so that they get a more rounded appearance. As a matter of fact form all shapes and edges to give them a rounded shape.

---

---

--- --- -----------------

Now as the base is finished the outer spikes will take form. Using a method similar to the base spikes apply a sphere of greenstuff (more blue in this is recommended as it will be stiffer and less prone to interact with the base spikes) and flatten it out using fingers and fingernails to lift the edge so that it floats above the base spikes. Several attempts to judge the amount of greenstuff used may be necessary to get the right shape/amount of greenstuff in place.

---

--- --- -----------------

After hardening use a micro pen to mark out the shape of a salamander/drake/dragon head. --- --- -----------------

Now use the scalpel to cut out the shape just like previously. Round the shapes and spikes as well to give them a less �sterile� appearance and cut out tiny teeth in the mouth of the drake but wait with the completion of the mouth itself.

This is also the time to remove the entire head from the shoulder pad as it will probably be covered with ugly cuts all along the soft plastic. Use a knife to remove the entire piece and this will also give you a perfect opportunity to complete the mouth as it is a difficult detail work and you now have access to the entire sculpt from all sides.

When you are satisfied with the result, use a tiny amount of superglue to place the sculpted head onto a new shoulder pad, plastic or metal. Make sure the new pad is washed and cleaned from fat as you�d really want things to stick to it this time.

Use a knife to carefully cut patches around the mouth, eye, end of mouth and nose to give the sculpt more depth. This will also greatly add in your ability to paint the drake head later on.

---

---

---

--- ---------------

Now fill the empty space between the very head and the rims of the shoulder pad with greenstuff. Flatten it out carefully so that the thickness is constant (up to the rim of the shoulder pad)

---

---

--- ----------------

Wait half an hour to make the greenstuff more hardened and less prone to deform and use a tool to press a scaly pattern into the greenstuff (sorry for the poor picture quality). When done make sure there is a narrow space between the greenstuff scales and the rims of the shoulder pad as well as the drake head.

As a tool I use a piece of plastic taken from the sprue and cut a tool out of it. Like a miniature shovel to press scaly patterns into the greenstuff.

---